Name:
Bis(trimethylsilyl)sulfate 98%
Synonym:
Sulfuric acid bis(trimethylsilyl)ester
Section 1 - Chemical Product
MSDS Name:Bis(trimethylsilyl)sulfate 98%
Synonym:Sulfuric acid bis(trimethylsilyl)ester
Section 2 - COMPOSITION, INFORMATION ON INGREDIENTS
| CAS# | Chemical Name | emsds | EINECS# |
| 18306-29-1 | Bis(trimethylsilyl)sulfate | 98 | 242-192-0 |
Hazard Symbols: F C Risk Phrases: 11 34 |
Section 3 - HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
Highly flammable. Causes burns.Moisture sensitive.
Potential Health Effects
Eye:
Causes eye burns. May cause lacrimation (tearing), blurred vision, and photophobia. May cause chemical conjunctivitis and corneal damage.
Skin:
Causes skin irritation and possible burns.
Ingestion:
Causes gastrointestinal tract burns. May cause systemic effects. May cause nausea, vomiting, abdominal pain, and increased salivation.
Inhalation:
Causes chemical burns to the respiratory tract. Aspiration may lead to pulmonary edema. May cause systemic effects. Olfactory fatigue may occur. Can produce delayed pulmonary edema.
Chronic:
Effects may be delayed.
Section 4 - FIRST AID MEASURES
Eyes: Get medical aid immediately. Do NOT allow victim to rub eyes or keep eyes closed. Extensive irrigation with water is required (at least 30 minutes).
Skin:
Get medical aid immediately. Immediately flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. Wash clothing before reuse. Destroy contaminated shoes.
Ingestion:
Do not induce vomiting. If victim is conscious and alert, give 2-4 cupfuls of milk or water. Never give anything by mouth to an unconscious person. Get medical aid immediately.
Inhalation:
Get medical aid immediately. Remove from exposure and move to fresh air immediately. If breathing is difficult, give oxygen. Do NOT use mouth-to-mouth resuscitation. If breathing has ceased apply artificial respiration using oxygen and a suitable mechanical device such as a bag and a mask.
Notes to Physician:
Section 5 - FIRE FIGHTING MEASURES
General Information:
As in any fire, wear a self-contained breathing apparatus in pressure-demand, MSHA/NIOSH (approved or equivalent), and full protective gear. During a fire, irritating and highly toxic gases may be generated by thermal decomposition or combustion. Dust can be an explosion hazard when exposed to heat or flame. Flammable solid.
May burn rapidly with flare burning effect. May re-ignite after fire is extinguished.
Extinguishing Media:
Do NOT use water directly on fire. For large fires, use water spray, fog or regular foam. Contact professional fire-fighters immediately.
For small fires, use dry chemical, carbon dioxide, sand, earth, water spray or regular foam. Cool containers with flooding quantities of water until well after fire is out.
Section 6 - ACCIDENTAL RELEASE MEASURES
General Information: Use proper personal protective equipment as indicated in Section 8.
Spills/Leaks:
Clean up spills immediately, observing precautions in the Protective Equipment section. Scoop up with a nonsparking tool, then place into a suitable container for disposal. Avoid generating dusty conditions. Remove all sources of ignition. Provide ventilation.
Section 7 - HANDLING and STORAGE
Handling:
Wash thoroughly after handling. Remove contaminated clothing and wash before reuse. Use only in a well-ventilated area. Minimize dust generation and accumulation. Do not breathe dust, vapor, mist, or gas. Do not get in eyes, on skin, or on clothing. Empty containers retain product residue, (liquid and/or vapor), and can be dangerous.
Keep container tightly closed. Keep away from heat, sparks and flame. Do not ingest or inhale. Discard contaminated shoes. Do not pressurize, cut, weld, braze, solder, drill, grind, or expose empty containers to heat, sparks or open flames.
Storage:
Keep away from heat, sparks, and flame. Keep container closed when not in use. Keep away from water. Refrigerator/flammables.
Section 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION
Engineering Controls:
Facilities storing or utilizing this material should be equipped with an eyewash facility and a safety shower. Use adequate general or local exhaust ventilation to keep airborne concentrations below the permissible exposure limits.
Exposure Limits CAS# 18306-29-1: United Kingdom, WEL - TWA: (listed as silica, amorphous): 6 mg/m3 (inhalable dust); 2.4 mg/m3 TWA (respirable dust) United Kingdom, WEL - STEL: (listed as silica, amorphous): 18 mg/ STEL (inhalable dust); 7.2 mg/m3 STEL (respirable dust) Russia: (listed as silica, amorphous): 1 mg/m3 TWA Personal Protective Equipment Eyes: Wear appropriate protective eyeglasses or chemical safety goggles as described by OSHAs eye and face protection regulations in 29 CFR 1910.133 or European Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin exposure.
Clothing:
Wear appropriate protective clothing to prevent skin exposure.
Respirators:
Follow the OSHA respirator regulations found in 29 CFR 1910.134 or European Standard EN 149. Use a NIOSH/MSHA or European Standard EN 149 approved respirator if exposure limits are exceeded or if irritation or other symptoms are experienced.
Section 9 - PHYSICAL AND CHEMICAL PROPERTIES
Physical State: Crystals
Color: moist white
Odor: None reported.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: 87-90 deg C @ 4 mm Hg
Freezing/Melting Point: 47-50 deg C
Autoignition Temperature: Not applicable.
Flash Point: Not applicable.
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water:
Specific Gravity/Density:
Molecular Formula: C6H18O4SSi2
Molecular Weight: 242.44
Section 10 - STABILITY AND REACTIVITY
Chemical Stability:
Stable under normal temperatures and pressures.
Conditions to Avoid:
Ignition sources, dust generation, excess heat, moist air.
Incompatibilities with Other Materials:
Strong oxidizing agents, moisture.
Hazardous Decomposition Products:
Carbon monoxide, irritating and toxic fumes and gases, carbon dioxide, silicon dioxide, sulfur oxides (SOx), including sulfur oxide and sulfur dioxide.
Hazardous Polymerization: Has not been reported.
Section 11 - TOXICOLOGICAL INFORMATION
RTECS#:
CAS# 18306-29-1 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
Bis(trimethylsilyl)sulfate - Not listed by ACGIH, IARC, or NTP.
Section 12 - ECOLOGICAL INFORMATION
Section 13 - DISPOSAL CONSIDERATIONS
Dispose of in a manner consistent with federal, state, and local regulations.
Section 14 - TRANSPORT INFORMATION
IATA
Shipping Name: FLAMMABLE SOLID, CORROSIVE, ORGANIC, N.O.S.*
Hazard Class: 4.1 (8)
UN Number: 2925
Packing Group: II
IMO
Shipping Name: FLAMMABLE SOLID, CORROSIVE, ORGANIC, N.O.S.
Hazard Class: 4.1 (8)
UN Number: 2925
Packing Group: II
RID/ADR
Shipping Name: FLAMMABLE SOLID, CORROSIVE, ORGANIC, N.O.S.
Hazard Class: 4.1
UN Number: 2925
Packing group: II
Section 15 - REGULATORY INFORMATION
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: F C
Risk Phrases:
R 11 Highly flammable.
R 34 Causes burns.
Safety Phrases:
S 9 Keep container in a well-ventilated place.
S 16 Keep away from sources of ignition - No
smoking.
S 25 Avoid contact with eyes.
S 33 Take precautionary measures against static
discharges.
WGK (Water Danger/Protection)
CAS# 18306-29-1: No information available.
Canada
None of the chemicals in this product are listed on the DSL/NDSL list.
CAS# 18306-29-1 is not listed on Canadas Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 18306-29-1 is not listed on the TSCA inventory.
It is for research and development use only.